Christmas: order by 12 December
Damastchef - Premium Damastmesser

How to fillet trout: raw or cooked

Raw trout into two fillets or cooked trout at the table without bones: both methods step by step, with the right knife and the mistakes to avoid.

5 min read · 11 November 2026

How to fillet trout: raw or cooked

Trout is the ideal fish for learning to fillet: easy to handle, with a clear bone structure and delicate flesh. There are two situations – you want to cut a raw trout into two fillets, or a cooked trout is on your plate and you want to eat it without bones.

You'll find both methods here, step by step.

What you need

  • an oven-ready, i.e. gutted, trout
  • a fillet knife with a narrow, slightly flexible blade
  • a large chopping board with a damp cloth underneath
  • kitchen paper and fish-bone tweezers

Filleting raw trout

Step by step

  1. Prepare: rinse the trout in cold water and pat it thoroughly dry. A dry fish doesn't slip. Lay it on the board with its back towards you.

  2. Cut behind the head: cut diagonally right behind the gill cover and pectoral fin until you meet the backbone. Don't cut through.

  3. Turn the knife: turn the blade flat so the edge points towards the tail and rests on the backbone.

  4. Release the fillet: run the knife in long, steady strokes along the backbone to the tail. Your free hand lies flat on the fish. You should feel the bones under the blade.

  5. Second fillet: turn the trout over and repeat the steps on the other side.

  6. Remove the belly bones: these sit at the thicker end of each fillet. Slide the knife flat underneath and cut them away with as little flesh as possible.

  7. Pull the pin bones: run your finger from head end to tail end along the middle of the fillet. Pull out the fine bones you feel with tweezers, in the direction they grow.

  8. Trim: cut off any remaining fins and ragged edges neatly.

Skin off or on?

For pan-frying, leave the skin on: it crisps up and holds the fillet together. For tartare, ceviche or smoking without skin, remove it:

  • Lay the fillet skin side down, tail end towards you.
  • Cut down to the skin at the tail end without cutting through it.
  • Hold the end of the skin, run the knife flat between skin and flesh and pull the skin against the blade while moving the knife gently back and forth.
Fillet knife - NATSUMI

In the shop · NATSUMI

Fillet knife

€119,00

Filleting cooked trout at the table

Trout meunière, blue trout or baked – a trout cooked whole is taken apart with a fish knife and fork, or with two forks.

Step by step

  1. Score the skin: score the skin along the back from head to tail, plus once across behind the head and in front of the tail fin.

  2. Remove the fins: pull out the dorsal fin together with the small bones attached to it and remove the belly fins.

  3. Peel off the skin: lift the skin at the head and pull it off towards the tail. With crispy pan-fried trout, it can stay on.

  4. Divide the top fillet: run the knife along the centre line you can see on the fillet and push the upper half up and the lower half down, off the bones.

  5. Lift off the bones: lift the skeleton at the tail and slowly pull it away towards the head. Head and bones come away in one piece.

  6. Lower fillet: remove the remaining belly bones at the edge. The lower fillet now lies boneless on the plate.

Don't forget: the cheeks behind the eyes are considered the most tender part of the trout.

The right knife

A fillet knife has a narrow blade that flexes slightly. This lets it follow the bones and take more flesh with it than a stiff knife. For trout, a blade length of 16 to 20 cm is enough.

More important than the shape is sharpness. How to keep the edge in shape is explained in our guide How to sharpen a knife.

Common mistakes

  • Wet fish: it slips. Always pat it thoroughly dry.
  • Angle too steep: the knife cuts into the fillet instead of along the bones. Keep the blade almost flat.
  • Sawing: lots of short cuts give a rough surface. Use long strokes.
  • Too much pressure: a sharp blade needs hardly any force. If you press, you'll crush the flesh.

The technique works just the same for char and salmon trout. How to break down other fish and flatfish is shown in our basic article How to fillet fish.

Frequently asked questions

How do you fillet a trout?

Cut diagonally behind the head down to the backbone, turn the knife flat and run it in long strokes along the bones to the tail. Then turn the trout over and repeat.

Do you need to scale trout before filleting?

Not necessarily. Trout scales are very small. If you want to eat the skin, you can scrape them off with the back of the knife from tail to head.

Does trout fillet have bones?

Yes, there's a row of fine pin bones in the middle of the fillet. Pull them out with fish-bone tweezers. With cooked trout, they usually come away with the skeleton.

Which knife for filleting trout?

A fillet knife with a narrow, slightly flexible blade of 16 to 20 cm. It should be very sharp.

What do I do with the head and bones?

You can make fish stock: simmer gently with soup vegetables, bay leaf and peppercorns for about 20 minutes, then strain.

Matching in the shop

Fillet knives

View all →

Share

To go with it

Read more